Satellites help link Texas earthquakes to wastewater injection, Stanford scientist says
Published on by Naizam (Nai) Jaffer, Municipal Operations Manager (Water, Wastewater, Stormwater, Roads, & Parks)
A 4.8 magnitude earthquake that rattled residents and damaged buildings in East Texas in 2012 was triggered by the injection of large volumes of wastewater from oil and gas activities into rocks deep beneath the surface, a new satellite study by Stanford scientists and others confirms.
Geophysicists have long suspected that the 2012 temblor, which was the largest ever recorded in the region and followed by several strong aftershocks, was a manmade, or “induced,” quake resulting from the activities of nearby wastewater injection wells, but definitive proof had been lacking – until now.
This wall collapsed in Timpson, Texas, following a 4.8 magnitude earthquake in 2012. A new satellite study confirms the temblor was induced by injection of large volumes of wastewater from oil and gas activities. (Image credit: East Texas Press)
“Our research is the first to provide an answer to the questions of why some wastewater injection causes earthquakes, where it starts and why it stops,” said study co-author William Ellsworth, a geophysics professor at Stanford’s School of Earth, Energy & Environmental Sciences.
In a new study, published in this week’s issue of the journal Science , Ellsworth and his co-authors used a remote sensing technique called Interferometric Synthetic Aperture Radar, or InSAR, to measure ground deformations near the wells in East Texas where the quake occurred. InSAR satellites use radar to detect tiny, centimeter-scale changes in the shape of Earth’s surface.
“Our study reports on the first observations of surface uplift associated with wastewater injection,” Ellsworth said. “The detection of uplift when combined with well-injection records provides a new way to study wastewater injection.”
The team focused on four high-volume wells used for disposing wastewater, located near the town of Timpson, Texas, where the 2012 quake was centered. The four wells began operations between 2005 and 2007 and at their peak injected about 200 million gallons of wastewater per year underground.
Brackish water naturally coexists with oil and gas within the Earth. After extracting this slurry using hydraulic fracturing or other techniques, drilling companies separate the “produced water” from the oil and gas and then reinject it into Earth at disposal wells. Approximately 180,000 of these disposal wells are currently in operation in the United States, primarily in Texas, California, Oklahoma and Kansas. “You can think of the wastewater as ancient ocean water,” Ellsworth said. “It’s too salty and too contaminated with other chemicals to treat economically, so the only viable solution at present is to put it back underground.”
But where that wastewater is injected can make a huge difference. Injecting wastewater at a depth of over 1 mile, two of the wastewater disposal wells the scientists examined lie directly above where the earthquake occurred. The other two wells injected similar volumes of wastewater, but at shallower depths, just over a half mile below the surface.
The InSAR measurements revealed that wastewater injection at the shallow wells resulted in detectable ground uplift up to 5 miles (8 kilometers) away but only a modest rise in pore pressure, which is the pressure of fluids within the fractures and cavities of rocks, at the depth at which earthquakes happen 2 or more miles below the surface.
Increasing pore pressure within a geologic fault can cause the two sides of the fault to slip and release seismic energy as an earthquake.
This did not happen at the shallow well sites in East Texas because a thick layer of nearly impermeable rock beneath the injection sites of the shallow wells prevented the pore pressure from migrating downward towards the crystalline basement, a deep and faulted rock layer where earthquakes originate. Instead, the injected wastewater caused a subtle uplift of several centimeters over a broad area around the injection wells.
The situation was different at the deep-well injection sites. There, the combination of stiffer rock and the impermeable “blocking formation” above allowed the rising pore pressure to migrate downward and build up until it triggered earthquakes in 2012 along an ancient fault line. The quakes ended in late 2013, when pressures began to decline after wastewater injections were scaled back considerably.
The new findings highlight the importance of understanding the local geology for wastewater injection operations, the scientists say. “The recent upturn in seismicity in Oklahoma and Kansas commonly happens where injection occurs close to the crystalline basement, so we’re getting lots of earthquakes in those places,” Ellsworth said. “Injecting at shallower depth above a blocking formation would reduce the ability of the pore pressures to migrate to the basement and activate the faults.”
The research also demonstrates the potential of remote sensing for understanding how and where pressure changes move through Earth. “Moving forward, we need to predict where pressures will increase in order to reduce the potential for inducing earthquakes,” Ellsworth said. “Our research uncovers new possibilities for operating wells in ways that reduce earthquake hazard.”
Additional authors on the study, titled “Surface uplift and time-dependent seismic hazard due to fluid injection in eastern Texas,” include Manoochehr Shirzaei of Arizona State University’s School of Earth and Space Exploration; Kristy Tiampo of the Cooperative Institute for Research in Environmental Sciences, University of Colorado Boulder; Pablo González of the University of Liverpool (UK); and Michael Manga of the University of California, Berkeley.
Attached link
http://news.stanford.edu/2016/09/22/satellites-link-texas-earthquakes-wastewater-injection/Taxonomy
- Water-Energy Nexus
- Fracking
- Fracking Technology