Increased pH of Permeate Water in Reverse Osmosis Plant
Published on by JOEL BAUTISTA, Técnico de Planta de Agua en Compañía Minera Antapaccay in Academic
Taxonomy
- Treatment
- Chemical Treatment
- Produced Water Treatment
- RO Systems
- Water Treatment & Control
- Purification
- Treatment Plants
- Reverse Osmosis
- Wastewater Treatment
- Water Treatment Solutions
- Industrial Water Treatment
- Reverse Osmosis
- Inorganic Chemicals
- Chemical Materials
- Utility Chemicals
- Treatment Chemicals
- water treatment
8 Answers
-
RO water has virtually no buffering capacity found in natural waters. As a result minor alterations have a great impact on the pH of the water. The most likely cause is the loss of soluble carbon dioxide due to pressure. The loss of CO2 from the water causes a rise a in pH
-
Mr. Joel.
Please confirm that rise in pH is along with rise in conductivity. If so then you need cleaning or replacement of membrane. If not then check the quality of feed water. pH of permeate depends on the composition of feed water. For further details please contact on rvsveipl@gmail.com. Prof. Rajendrakumar V Saraf, Chairman Viraj Envirozing India Pvt. Ltd. Pune, India
1 Comment
-
Only pH, conductivity is normal, very low.
-
-
Yes, similar to the sentiments of Mr. Lipshultz. The loss of membrane rejection is an indication of increasing permeate conductivity and subsequently a typically higher pH of the permeate water. To regain rejection efficiency, a potential membrane cleaning may work or a membrane replacement would be required if the cleaning is not sufficient.
-
What means increase? Normally decrease from pH numbers, as CO2 pass the membrane, therefore you will find more acidic water.
-
Dear Joel
Good question,
Following reason to increase the pH
- The declining pH will cause the ORP reading to increase even if no chlorine is present.
- The pH difference after the RO depends on the composition of your input water source. The resultant pH will depend on the initial water chemistry.
- Depending on whether you have amounts of gases such as CO2 in your local water supply.
- The membrane got exhausted and not capable to remove alkaline minerals.
- Rejected water line got choked.
Regards,
Prem Baboo
-
- Changes in the feed water.
- Fouling, indicating necessity of chemical cleanings.
- Damage of the membranes increasing the salts passage.
- Improper dosage of conditioning chemicals, antiscalant for instance.1 Comment
-
Thank you for your response. In this case, conductivity is ok and the membranes are new.
-
-
Hello Mr. Bautista,
If membranes need cleaning or replacement it will also show changes in permeate EC and flows. If everything is fine then, Try lowering pressure and increasing reject flow to get desired pH. Increased pH in permeate has also dependency on antiscalent used. Please do check antiscalent properties.
Regards,
Abhishek Nirakhe.
1 Comment
-
Thank you. In this case the membranes are new and the conductivity is ok.
-
-
Dear Mr. Bautista,
If the membranes are showing proper rejection however, the pH is increasing and / or same as source water, it is a sign the membrane rejection will soon reduce requiring cleaning or replacement.
Warmest regards,
FOR THE BEST TASTE IN LIFE
Celebrating 40 Years Pure Excellence
...into another Half Century re-inventing the water industry !
Think Aquathin...AquathinK !
( visit the all new www.aquathin.com )
** AN ISO9001:2000, ISO9001:2008 , ISO9001:2015 QMS REGISTERED / CERTIFIED COMPANY - (IMS 0192, NQA 12635) **
& 2008 PRESIDENT'S E STAR AWARD RECIPIENT ( visit www.aquathin.com/estar2008.pps )
Alfie
Alfred J. Lipshultz
President & CEO
Aquathin Business Center / 950 South Andrews Avenue / Pompano Beach, FL 33069
T 954 781 7777 / F 954 781 7336 /E info@aquathin.com / Skype aquathinhq.alfie